Hass hydraulic calculation software error

#Hass hydraulic calculation software error update
#Hass hydraulic calculation software error upgrade
#Hass hydraulic calculation software error download

Check that the I/O PCB has power by looking for the 12/24V green leds. Refer to Next Generation Control - I/O PCB Main Firmware - UpdateВ procedure.Д¬ommunication has been lost to the I/O PCB.

#Hass hydraulic calculation software error update

Update the I/O PCB Main firmware to the latest 03.xx version.

Update the I/O PCB Tool Changer firmware to the latest 01.xx version.Update the I/O PCB Main firmware to the latest 02.xx version.

#Hass hydraulic calculation software error upgrade

Upgrade the I/O PCB Tool Changer firmware to the latest 01.xx version.

Inspect the tool changer relays, make sure the relay sockets are solder into the PCB board. Power off, and inspect the circuit components on the I/O PCB, see section below.ДЄn internal I/O circuit board error has been sensed where the main and tool changer microcontrollers could not communicate.

#Hass hydraulic calculation software error download

I/O PCB (34-348xC) Main Firmware 02.05 and higherДЄttempts were made to download an I/O configuration file while configuration memory was locked.ДЄn internal I/O circuit board error has been sensed in it's shift chain. Refer to the E-Stop - DebounceВ procedure.

The doors closing have shaken the estop and caused a momentarily disconnect and caused an estop of the machine.ДЄ debounce capacitor will need to be added to the I/O PCB. Machine with an auxiliary estop generates an estop alarm after the closing of machine doors. Machine generates multiple Alarm 20014.1 SIO TOOL CHANGER PCB IS NOT PRESENT and 20014.0 SIO TOOL CHANGER PCB PRESENT after the I/O TC PCB is installed.

Inspect the wiring, pins, and connectors for this circuit. There is a problem with the 120 VAC outputs circuit components (solenoids, Wye-Delta, Oil Pump etc.) There is a problem with one of the tool changer relays. Inspect the tool changer circuit components on the I/O PCB, see section below.ДЄlarm 858 ATC CAROUSEL MOTOR ELECTRICAL FAULT There is a component failure on the I/O PCB. Intermitten Alarm 115В CAROUSEL POSITION FAULT. Refer to: Next Generation Control - Power On/Off Circuit, Main Transformer - Troubleshooting Guide. The machine detected a open circuit from the thermal switch at the transformer. Refer to Next Generation Control - I/O PCB Main Firmware - Update. Update I/O Main and TC firmware version to the latest.

Inspect the RJ-45 connector on the Maincon PCB & I/O PCB for bent pins.ДЄlarm 9924 CONTROL AND IO BOARD COMMUNICATION LOSTВ is generated during a Tool ChangerВ cycle and Tool ChangerВ motion continues.

If they are not lit it could be an indication that a phase is missing, trace the 3-phase power to the source.

Make sure the Traffic, TC Comms, Loop, 15 Vdc, 12Vdc, and 24Vdc LEDs are lit.

Inspect the cable from PSUP(P17) to I/O PCB (P56), pull on each wire to make sure the pin is correctly locked in the housing.

Check the 3-Phase power input from PSUP(P4) to I/O PCB (P55).

To test the cable refer to Network Cable Tester ToolВ procedure.

Check the RJ-45cable connection from Maincon PCB (J14) to I/O PCB (J4).

The I/O PCB board lost communications with the Maincon PCB. Multiple Alarms or 9924В CONTROL AND IO BOARD COMMUNICATION LOST 9925В CONTROL AND IO BOARD COMMUNICATION DID NOT INITIALIZE and all the input values on the diagnostic page show XX. Reload the I/O PCB main firmware refer to Next Generation Control - I/O PCB Main Firmware - Update. The firmware update failed, or I/O firmware is corrupted. The Main CRC and the Factory CRC are now the same.ДЄlarm 9933В SOFTWARE VERSION MISMATCH and 9100 If the alarm does not clear, cycle the machine power.

Go toВ I/O ConfigВ in theВ DiagnosticsВ tab.

Note:В The USB memory device must contain your Haas Control KeyВ and the correct configuration files.

Put the USB memory device into the control.

Main CRC and Factory CRC do not match due to the I/O PCB being swapped out. Alarm 9100В NON RESETTABLE SOFTWARE ERROR at Power On, or Alarm 9915В IO BOARD CONFIGURATION MISMATCH.